(FM8) SEMCON LAND ROVER OWNER GUIDE VER 1.00 EURO
LANGUAGE: english-en; MARQUE: landrover; MODEL: L319
L
Tyre repair kit
10.
11.
Set the compressor switch to the on (I)
position.
CHECKING THE TYRE PRESSURE
AFTER A REPAIR
Inflate the tyre to a minimum of 1.9 bar (26
psi) and a maximum of 3.5 bar (51 psi).
When driving the vehicle, if you
experience vibrations, abnormal
steering, or noises, reduce speed
immediately. Drive with extreme
caution and reduced speed, to the first
safe place to stop the vehicle. Visually
examine the tyre and check its
pressure. If there are any signs of
damage or deformity to the tyre, or the
tyre pressure is below 1.3 bar (19
psi), do not continue driving.
•
When pumping the sealant through the
tyre valve, the pressure may rise up to
6
again after approximately 30 seconds.
bar (87 psi). The pressure will drop
12.
During the inflation, switch the
compressor off briefly, to check the tyre
pressure using the gauge mounted on the
compressor.
•
It should not take longer than seven
minutes to inflate the tyre. If, after
seven minutes, the tyre has not yet
reached minimum pressure, the tyre
should not be used.
Consult a tyre repair centre or your
Dealer/Authorised Repairer, for
advice concerning the replacement of
a tyre after using a tyre repair kit.
13.
Once the tyre has been inflated, switch off
the compressor. If desired, the engine may
be turned off after the compressor has
been turned off.
1. Drive the vehicle for 3 km (2 miles) then
stop in a safe place. Carry out a visual
examination of the tyre’s condition.
2.
Make sure that the sealant container
section is in its original position.
14.
15.
Remove the power connector from the
auxiliary power socket.
3.
Screw the inflation hose connector firmly
onto the tyre valve.
Remove the inflation hose from the tyre
valve, by unscrewing it as quickly as
possible (anticlockwise).
4.
5.
Read the tyre pressure from the gauge.
If the pressure of the sealant filled tyre is
above 1.3 bar (19 psi) adjust the pressure
to the correct value.
16.
17.
Replace the inflation hose protective cap
and the tyre valve cap.
Ensure that the tyre repair kit (including the
bottle and receiver caps) are placed
securely in the vehicle. You will need to use
the kit to check the tyre pressure after
approximately 3 km (2 miles), so ensure
they are easily accessible.
6.
Ensure that the compressor switch is in the
off (O) position and insert the power cable
connector into the auxiliary power socket.
If the vehicle is in a well ventilated area,
start the engine.
7.
8.
Switch the compressor to on (I) and inflate
the tyre to the correct pressure.
18.
Immediately drive the vehicle for
approximately 3 km (2 miles), to allow the
sealant to coat the inner surface of the tyre
and form a seal at the puncture.
To check the tyre pressure, turn off the
compressor then read the pressure from
the gauge.
168
| Categories | Land Rover, Land Rover Discovery 4 |
|---|---|
| Tags | Land Rover |
| Model Year | 2014, 2015 |
| Download File |
|
| Document Type | Owners Manual |
| Language | English |
| Product Name | Discovery 4 Handbook |
| Product Brand | Land Rover |
| Document File Type | |
| Publisher | landrover.com |
| Wikipedia's Page | http://en.wikipedia.org/wiki/Land_Rover |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Automotive readers have rated 2014-2015 Land Rover Discovery 4 Handbook Manual 5.0 out of 5.0 based on 1 product reviews. This website is really Great1!