Features
234
not be long enough for the integrated signal RWhen aiming the garage door remote
transmitter to pick up the signal during
programming. Similar to this Canadian law,
some U.S. gate operators are designed to
"time-out" in the same manner.
If you live in Canada or have difficulties
programming the garage door opener
(regardless of where you live) when using the
control at the transmitter buttons on the
rear-view mirror, hold garage door remote
controlA at differing distances and angles
from the transmitter button that you are
programming. Try different angles from a
distance of 2 to 12 inches (5 to 30 cm) or
the same angle from differing distances.
programming steps (see above), proceed as RIf there is another garage door remote
follows:
control for the same device, perform the
programming steps again using the remote
control. Before performing these steps,
make sure that new batteries have been
installed in the garage door remote control.
RAlign the antenna cable of the garage door
opener unit. This can improve signal
reception/transmission.
X Press transmitter button (;,= or?) and
hold it down during the following steps until
the setup has been completed
successfully.
X At the same time, press transmitter button
B of the garage door remote control for
two seconds, then release it for two
seconds, then press it again for two
seconds.
Opening or closing the garage door
X Repeat this sequence on transmitter
buttonB of the garage door remote
Once programmed, the integrated remote
control will assume the function of the garage
control until the frequency signal has been door system's remote control. Please also
learned.
X If the setup procedure is successful,
read the operating instructions for the garage
door system.
indicator lamp: flashes once slowly and X Turn the SmartKey to position 2 in the
goes out after a few seconds.
X Continue with the other programming
steps (see above).
ignition lock.
X Press transmitter button;,= or? in the
overhead control panel that you have
programmed to operate the garage door.
Garage door system with fixed code:
indicator lamp: lights up continuously.
Problems when programming
If you have problems when programming the
integrated remote control, please note the
following:
Garage door system with rolling code:
indicator lamp: flashes briefly and then
lights up for approximately two seconds.
This is repeated for up to 20 seconds.
Rcheck the transmitter frequency of garage
door remote controlA (which can usually
be found on the rear of the remote control).
The integrated remote control is
compatible with equipment that operates
in the frequency range 280 to 390 MHz.
Rreplace the batteries in garage door remote
controlA. This increases the likelihood of
garage door remote controlA sending a
strong and precise signal to the integrated
remote control on the rear-view mirror.
i The transmitter will transmit a signal for
as long as the transmitter button is being
pressed. The transmission will be halted
after a maximum of 20 seconds and
indicator lamp: will flash. Press the
transmitter button again, if necessary.
| Categories | Mercedes-Benz C-Class Manuals, Mercedes-Benz Manuals |
|---|---|
| Tags | Mercedes-Benz C250, Mercedes-Benz C300, Mercedes-Benz C350, Mercedes-Benz C63 AMG, Mercedes-Benz W204 |
| Model Year | 2011 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(6 votes, average: 4.83 out of 5)
Automotive readers have rated 2011 Mercedes-Benz C250 C300 C350 4MATIC C63 AMG W204 Owners Manual 4.8 out of 5.0 based on 6 product reviews. Excellent site, useful for persons needing more understanding of c-class models
Very good, if I will downaload it, thanks! But why your website first ask write good review, and then you let download?
Engine temperature need to check with owner manual
it's a very useful documents, when u lost your user manual!it's a very useful documents, when u lost your user manual!
userful documents, when you get lost your manual
Comments are closed.