DO-IT-YOURSELF MAINTENANCE
3.
Slide underneath the car and loosen the
drain plug by turning it counterclockwise
with a wrench of the proper size. Be sure
that a drain pan is in position to catch the oil
as it drains out, then remove the drain plug.
8. Start the engine and check to be sure no oil
is leaking from the drain plug or oil filter.
9. Shut off the engine and recheck the oil level.
G050B01A-AAT
Recommended Engine Coolant
NOTE:
Always dispose of used engine oil in an
environmentallyacceptablemanner. It issug-
gested that it be placed in a sealed container
and taken to a service station for reclama-
tion. Do not pour the oil on the ground or
put it into the household trash.
WARNING:
Be very careful when draining the engine oil
as it may be hot enough to burn you!
4.
When the oil has stopped draining, replace
the drain plug using a new washer and
retighten by turning it clockwise.
WARNING:
Used motor oil may cause irritation or can-
cer of the skin if left in contact with the skin
for prolonged periods of time. Wash your
hands thoroughly with soap and warm wa-
ter as soon as possible after handling used
oil.
HGK187
Tightening torque is:
4.5
4.5
~ 4.0 kgf.m (2.0L)
~ 3.5 kgf.m (2.7L)
Use a high quality ethylene-glycol coolant in a
mix with water. The engine coolant should
50/50
be compatible with aluminum engine parts.
Additionalcorrosioninhibitorsoradditivesshould
not be used. The cooling system must be main-
tained with the correct concentration and type
of engine coolant to prevent freezing and corro-
sion. Never allow the concentration of anti-
freeze to exceed the 60% level or go below the
5.
6.
Remove the oil filter by turning it counter-
clockwise with a oil filter wrench of the
proper size. A certain amount of oil will
come out when you remove the filter. So be
sure to have your drain pan in place under-
neath it.
Install a new oil filter in accordance with the
instructions on the carton or on the filter
itself. Do not over-tighten. (Tightening
torque : 1.2 ~ 1.6 kgf.m)
Be sure that the mounting surface on the
engine is clean and that the old gasket is
removed completely. Lubricate the new gas-
ket on the filter with clean engine oil before
installation.
Refill the crankcase with the recommended
engine oil. Refer to the specification in chap-
ter 9 for engine oil capacity.
G050A01A-AAT
CHECKING AND CHANGING THE EN-
GINE COOLANT
35%
level, or damage to the cooling system
may result. For proper concentration when add-
ing or replacing the engine coolant, refer to the
following table.
WARNING:
Do not remove the radiator cap when the
engine is hot. When the engine is hot, the
engine coolant is under pressure and may
erupt through the opening if the cap is
removed. You could be seriously burned if
you do not observe this precaution. Do not
remove the radiator cap until the radiator is
cool to the touch.
7.
6-5
| Categories | Hyundai Manuals, Hyundai Tiburon Manuals |
|---|---|
| Tags | Hyundai Tiburon 2.0, Hyundai Tiburon 2.7 |
| Model Year | 2003 |
| Download File |
|
| Document Type | Owners Manual |
| Language | English |
| Product Brand | Hyundai, Tiburon |
| Document File Type | |
| Copyright | Attribution Non-commercial |
(2 votes, average: 4.5 out of 5)
Automotive readers have rated 2003 Hyundai Tiburon Owners Manual 4.5 out of 5.0 based on 2 product reviews. thanks