2008 Kia Borrego Owners Manual

Features of your vehicle
Standard programming
To   train   most   devices,   follow   these
instructions:
6. To
program    the     remaining    two
HomeLink    buttons,   follow  steps   2
®
through 5.
If there is difficulty locating the training
button,  reference the  device  owner's
manual or please visit our Web  site at
www.homelink.com.
2. Firmly press and release the "learn" or
"smart"   button  (which   activates  the
"training light").
1.
For first-time programming,  press and
hold     the    two     outside     buttons,
Rolling code programming
HomeLink
®
Channel 1  and Channel 3
Rolling  code  devices  which are  "code-
protected" and  manufactured after  1996
may be determined by the following:
Buttons, until the indicator light begins
to  flash  (after  20  seconds). Release
both buttons.  Do not hold  the buttons
for longer than 30 seconds.
NOTICE
There are 30 seconds in which to initiate
step 3.
Reference the  device owner's  manual
for verification.
2.
3.
4.
Position  the   end  of  your  hand-held
transmitter  2-8 cm  (1-3 inches)  away
The  handheld  transmitter  appears  to
program   the   HomeLink
®
Universal
Transceiver  but does  not  activate the
device.
from   the  HomeLink
®
buttons   while
3. Return to the vehicle and firmly  press,
hold for two seconds and then release
keeping the indicator light in view.
Simultaneously  press  and  hold  both
®
the  HomeLink   and  hand-held  trans-
mitter button. DO NOT release the but-
tons until step 4 has been completed.
Press and  hold the  trained HomeLink
button. The device has the rolling code
feature if the indicator light flashes rap-
idly  and then  turns  solid after  2  sec-
onds.
the desired HomeLink  button.  Repeat
®
the  "press/hold/release"  sequence  a
second time to complete the  program-
ming. (Some devices may  require you
to repeat this sequence a  third time to
complete the programming.)
While  continuing  to hold  the  buttons
the red Indicator  Status LED will flash
slowly
and     then     rapidly     after
4.
5.
Press
HomeLink
and
hold
the
just-trained
To train rolling code devices, follow these
instructions:
HomeLink   successfully  trains  to  the
®
frequency  signal  from  the  hand-held
transmitter. Release both buttons.
®
button and observe the red
Status  Indicator  LED. If  the  indicator
light stays on constantly, programming
is  complete  and  your  device  should
activate.
1.
At  the  garage  door  opener  receiver
(motor-head unit) in the garage, locate
the "learn" or  "smart" button. This can
usually  be  found  where the  hanging
antenna wire is attached to  the motor-
head unit. Exact  location and  color of
the  button may  vary  by  garage  door
opener brand.
5.
Press
and    hold    the   just-trained
HomeLink  button and observe the red
®
Status  Indicator  LED. If  the  indicator
light stays on constantly, programming
is  complete  and  your  device  should
To
HomeLink
program
the
remaining
two
®
buttons, follow either steps
1
through  4  above  for  other  Rolling
activate when the HomeLink  button is
®
pressed and released.
Code devices  or steps 2  through 5  in
Standard  Programming   for  standard
devices.
4
44
Product Specification
CategoriesKia Borrego Manuals, Kia Manuals
Model Year2008
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 425 pages
Document File TypePDF
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field