Vehicle data
370
!
Only add coolant that has been premixed The coolant is checked at every service date
with the desired antifreeze protection. You at an authorized Mercedes-Benz Center.
could otherwise damage the engine.
The antifreeze/corrosion inhibitor
Further information on coolants and on
filling can be found in the Mercedes-Benz
Specifications for Service Products, MB
Approval 310.1, e.g. on the Internet at
http://bevo.mercedes-benz.com. You
can also consult an authorized Mercedes-
Benz Center.
concentration in the cooling system should:
Rbe at least 50%. This will protect the cooling
system against freezing down to around
-35
‡ (-37 †).
Rnot exceed 55% (antifreeze protection
down to -49 ‡ (-45 †); otherwise, heat will
not be dissipated as effectively.
!
Always use a suitable coolant mixture,
even in countries where high temperatures
prevail.
If the coolant level is too low, MB 326.0
antifreeze/corrosion inhibitor should be
added. Have the cooling system checked for
leaks.
Otherwise, the cooling system will not be
sufficiently protected from corrosion, and
the boiling point will be too low.
Windshield and headlamp cleaning
system
If the coolant has antifreeze protection down
to -35 ‡ (-37 †), the boiling point of the
coolant in the pressurized system is
approximately 266 ‡ (130 †).
Your vehicle has a range of aluminum
components. Use of aluminum components
in the engine make it necessary to specifically
match the antifreeze/corrosion inhibitor in
these systems in order to protect the
aluminum parts. Using other antifreeze/
corrosion inhibitors without these
G Warning
Washer solvent/antifreeze is highly
flammable. Do not spill washer solvent/
antifreeze on hot engine parts, because it may
ignite and burn. You could be seriously
burned.
X Use MB Windshield Washer Concentrate
MB SummerFit.
X At temperatures above freezing: add 1
part MB SummerFit to 100 parts water, e.g.
1.34 fl oz (40 ml) MB SummerFit to 1 gal
(4.0 l) of water.
characteristics affects the service life.
The coolant must be used throughout the year
in order to maintain the necessary corrosion
protection and provide protection from
overheating. In the Service Booklet, you can
find information on the intervals for renewal.
X At temperatures below freezing: add 1
part MB SummerFit to 100 parts washer
fluid, e.g. 1.34 fl oz (40 ml) MB SummerFit
to 1 gal (4.0 l) of water.
The renewal interval is determined by the
coolant type and the cooling system design.
The renewal interval in the Service Booklet is
only valid if the coolant is added or renewed
with Mercedes-Benz approved products.
Therefore, only use MB 326.0 antifreeze/
corrosion inhibitor or another Mercedes-Benz
approved product of the same specification.
Vehicle data
Vehicle data, GL 350 BlueTEC
(164.825)
Information on other Mercedes-Benz
approved products of the same specification
can be obtained at any authorized Mercedes-
Benz Center or on the Internet at
The data quoted here refers specifically to a
vehicle with standard equipment. Contact an
authorized Mercedes-Benz Center for the
data for all vehicle variants and trim levels.
http://bevo.mercedes-benz.com.
| Categories | Mercedes-Benz GL-Class Manuals, Mercedes-Benz Manuals |
|---|---|
| Tags | Mercedes-Benz GL350 BlueTEC, Mercedes-Benz GL450, Mercedes-Benz GL550, Mercedes-Benz X164 |
| Model Year | 2011 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)