Switch on the device and allow to run for
approx. 3 minutes to fill wheel with sealant.
It is not important what inflation pressure
the tire has after filling.
respondingly trained personnel if the tire can-
not be made ready for driving with the
M Mobility System.<
The tire inflation pressure must be at least
29 psi/200 kPa. Otherwise do not con-
tinue driving.<
9.
Switch off device.
10.
Remove connecting hose from connection
of sealant bottle and tire valve.
Stow the M Mobility System in the vehicle
again.
Continue driving
Do not exceed the permissible maximum
speed of 50 mph/80 km/h, otherwise
accidents can occur.<
Distributing sealant
Immediately drive approx. 2 miles/3 km so that
sealant is evenly distributed in tire.
Reinitialize the Flat Tire Monitor.
For details, refer to page 87.
Have the defective tire and the sealant bottle of
the M Mobility System replaced as soon as
possible.<
Do not exceed a maximum speed of
35
mph/60 km/h. Do not drop below
12
mph/20 km/h if possible.<
Producing tire inflation pressure
Changing wheels*
1.
2.
3.
4.
After approx. 2 miles/3 km, stop at suitable
location.
Safety precautions in the event of a flat
tire or wheel change: Park the vehicle as
far as possible from passing traffic and on solid
ground. Switch on the hazard warning flashers.
Apply the handbrake and shift into first gear or
reverse with the manual transmission, or move
the selector lever into a drive position with the
sequential transmission.
Screw compressor hose 9 directly onto tire
valve.
Insert connector 3 in lighter socket in vehi-
cle interior.
Correct tire inflation pressure to 29 psi/
200
kPa. With the ignition switched on:
>
Increase inflation pressure: Switch on
the device, position I. To check the cur-
rent inflation pressure setting, briefly
switch off the device.
Have all vehicle occupants get out of the vehicle
and ensure that they remain outside the imme-
diate area in a safe place, such as behind a
guardrail.
If a warning triangle* or portable hazard warning
lamp* is required, set it up on the roadside at an
appropriate distance from the rear of the vehi-
cle. Comply with all safety guidelines and regu-
lations.
Change the wheel only on a level, firm surface
which is not slippery. The vehicle or the jack
could slip to the side if you attempt to raise the
vehicle on a soft or slippery surface such as
snow, ice, tiles, etc.
Position the jack on a firm support surface.
Do not use a wooden block or similar object as a
support base for the jack, as this would prevent
it from extending to its full support height and
reduce its load-carrying capacity.
Do not allow compressor to run
longer than 10 minutes, otherwise
the device will overheat and may be dam-
aged.<
>
Reduce inflation pressure: press
button 8 or turn screw 8 on pressure
gauge.
If the inflation pressure is not held, drive
the vehicle again, refer to Distributing
sealant. Then repeat steps 1 to 4 once.
Using the M Mobility System can be ineffective
with tire damage from a size of approx. 0.16 in/
mm. Please contact the nearest BMW center,
4
refer to page 234, or a workshop that works
according to BMW repair procedures with cor-
To avoid serious or fatal injury: never lie under
228
Online Edition for Part no. 01 41 2 600 775 - © 08/08 BMW AG
| Categories | BMW 6-Series Manuals, BMW Manuals |
|---|---|
| Tags | BMW 650i, BMW E63, BMW E64, BMW M6 |
| Model Year | 2009 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)