204_AKB;
d2ureepe,
3; 69, en-US
2009-05-11T16:20:59+02:00 - Seite 219
Version: 2.11.8.1
Useful features
219
control, or simply for continued use as a
hand-held remote control to operate the
respective device in other situations.
Programming tips
If you are having difficulty programming the
integrated remote control, here are some
helpful tips:
Reprogramming a single signal
transmitter button
RCheck the frequency of hand-held remote
controlA (typically located on the reverse
side of the remote). The integrated remote
control is compatible with radio-frequency
devices operating between 280-390 MHz.
To program a device using a signal
transmitter button previously trained, follow
these steps:
X Switch on the ignition.
RPut a new battery in hand-held remote
controlA. This will increase the likelihood
of the hand-held remote control sending a
stronger and more accurate signal to the
integrated remote control.
X Press and hold the desired signal
transmitter button (;,= or?). Do not
release the button.
Indicator lamp: will begin to flash after
20
seconds.
RWhile performing step 3, hold hand-held
remote controlA at different lengths and
angles from the signal transmitter button
X Without releasing the signal transmitter
button, proceed with programming starting
with step 3.
(
;,= or?) you are programming.
Attempt varying angles at the distance of 2
to 12 inches (5 to 30 cm) away or the same
angle at varying distances.
Operation of integrated remote control
X Switch on the ignition.
X Select and press the appropriate
integrated signal transmitter button (;,
RIf another hand-held remote control is
available for the same device, try the
programming steps again using that other
hand-held remote control. Make sure new
batteries are in the hand-held remote
control before beginning the procedure.
=
or?) to activate the remote controlled
device.
The integrated remote control transmitter
continues to send the signal as long as the
button is pressed – up to 20 seconds.
RStraighten the antenna wire from the
garage door opener assembly. This may
help improve transmitting and/or receiving
signals.
Erasing the integrated remote control
memory
i If you sell your vehicle, erase the codes of i Certain types of garage door openers are
all three channels.
incompatible with the integrated remote
control. If you should experience further
difficulties with programming the
integrated remote control, contact an
authorized Mercedes-Benz Center, or call
the Mercedes-Benz Customer Assistance
X Switch on the ignition.
X Simultaneously press and hold outer signal
transmitter buttons; and?, for
approximately 20 seconds, until indicator
lamp: flashes rapidly. Do not hold for
longer than 30 seconds.
Center (USA only) at
1-800-FOR-MERCedes, or the HomeLink®
The codes of all three channels are erased.
Hotline (USA only) at 1-800-355-3515, or
the Customer Service (Canada only) at
1-800-387-0100.
Z
| Categories | Mercedes-Benz C-Class Manuals, Mercedes-Benz Manuals |
|---|---|
| Tags | Mercedes-Benz C-Class, Mercedes-Benz C250, Mercedes-Benz C300, Mercedes-Benz C350, Mercedes-Benz C63 AMG, Mercedes-Benz W204 |
| Model Year | 2010 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(3 votes, average: 4.67 out of 5)
Automotive readers have rated 2010 Mercedes-Benz C-Class Operators Manual C250 C300 4MATIC C350 Sport C63 AMG 4.7 out of 5.0 based on 3 product reviews. Really enjoy the ride though it’s my first Mercedes car . Have used other cars like VW touareg , Audi and Bmw but never owned a Mercedes so it’s exciting for me
it is very good
really excellent
Great