204_AKB;
d2ureepe,
3; 69, en-US
2009-05-11T16:20:59+02:00 - Seite 356
Version: 2.11.8.1
Fuels, coolants, lubricants, etc.
356
the use of quality gasoline containing
The cooling system was filled at the factory
additives that prevent the build-up of carbon with a coolant providing freeze protection to
deposits.
approximately -35‡ (-37†) and corrosion
protection.
After an extended period of using fuels
without such additives carbon deposits can
build up, especially on the intake valves and
in the combustion area, leading to engine
performance problems such as:
!
Add premixed coolant solution only.
Adding water and MB 325.0 Anticorrosion/
Antifreeze separately from each other,
could cause engine damage not covered by
the Mercedes-Benz Limited Warranty.
RWarm-up hesitation
RUnstable idle
If the antifreeze mixture is effective to -35‡
(-37†),
pressurized cooling system is reached at
approximately 266‡ (130†).
the boiling point of the coolant in the
RKnocking/pinging
RMisfire
RPower loss
The coolant solution must be used year round
to provide the necessary corrosion protection
and increase boil-over protection. Refer to
the Maintenance Booklet for replacement
interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance Booklet is only applicable if
MB 325.0 Anticorrosion/Antifreeze solution
or other Mercedes-Benz approved products
of equal specification are used to renew the
coolant concentration or bring it back up to
the proper level.
In areas where carbon deposits may be
encountered due to lack of availability of
gasoline which contains these additives, the
use of Mercedes-Benz approved additives is
recommended.
Contact an authorized Mercedes-Benz Center
or visit www.mbusa.com (USA only) for a
listing of approved products. Follow
directions on the product label.
Do not blend other fuel additives with fuel.
This only results in unnecessary cost and may
be harmful to the engine operation.
!
Damage or malfunction resulting from
For information on other Mercedes-Benz
approved products of equal specification,
contact an authorized Mercedes-Benz Center
or visit www.mbusa.com (USA only).
To provide important corrosion protection,
the solution must be at least 50%
anticorrosion/antifreeze (equivalent to
freeze protection to approximately -35‡
[-37†]).
poor fuel quality or from blending additional
fuel additives other than those tested and
approved by us for use on Mercedes-Benz
vehicles are not covered by the Mercedes-
Benz Limited Warranty or by any pre-owned
or Extended Limited Warranties.
Coolants
If you use a solution that is more than 55%
The engine coolant is a mixture of water and anticorrosion/antifreeze (freeze protection
anticorrosion/antifreeze, which provides:
to approximately -49‡ [-45†]), the engine
temperature will increase due to the lower
heat transfer capability of the solution.
Therefore, do not use more than this amount
RCorrosion protection
RFreeze protection
RBoiling protection (by increasing the boiling of anticorrosion/antifreeze.
point)
If the coolant level is low, water and MB 325.0
Anticorrosion/Antifreeze should be used to
bring it up to the proper level (have cooling
| Categories | Mercedes-Benz C-Class Manuals, Mercedes-Benz Manuals |
|---|---|
| Tags | Mercedes-Benz C-Class, Mercedes-Benz C250, Mercedes-Benz C300, Mercedes-Benz C350, Mercedes-Benz C63 AMG, Mercedes-Benz W204 |
| Model Year | 2010 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(3 votes, average: 4.67 out of 5)
Automotive readers have rated 2010 Mercedes-Benz C-Class Operators Manual C250 C300 4MATIC C350 Sport C63 AMG 4.7 out of 5.0 based on 3 product reviews. Really enjoy the ride though it’s my first Mercedes car . Have used other cars like VW touareg , Audi and Bmw but never owned a Mercedes so it’s exciting for me
it is very good
really excellent
Great