R
Tyrerepairkit
5.
6.
Remove the valve cap from the damaged
tyre.
14. Replace the inflation hose protective cap
and the tyre valve cap.
Remove the protective cap from the inflation
hose. Connect the inflation hose to the tyre
valve making sure the hose is screwed on
firmly.
15. Make sure the tyre repair kit (including the
bottle and receiver caps) are placed securely
in the vehicle. You will need to use the kit
to check the tyre pressure after a maximum
of 3 km (2 miles), so make sure they are
easily accessible.
7.
Making sure the compressor switch is in
the Off (0) position, insert the power cable
connector into an auxiliary power socket,
see 82, STORAGE COMPARTMENTS.
Then switch on the ignition, see 97,
SWITCHING ON THE IGNITION.
16. Immediately drive the vehicle for a
maximum of 3 km (2 miles), to allow the
sealant to coat the inner surface of the tyre
and form a seal at the puncture.
8.
9.
Switch on the compressor by positioning
the switch to the (l) position.
CHECKING THE TYRE PRESSURE
AFTER A REPAIR
Inflate the tyre to a minimum of 1.8 bar (26
psi, 180 kPa) and a maximum of 3.5 bar
When driving the vehicle, if you
experience vibrations, abnormal
steering, or noises, reduce speed
immediately. Drive with extreme
caution and reduced speed, to the first
safe place to stop the vehicle. Visually
examine the tyre and check its
pressure. If there are any signs of
damage or deformity to the tyre, or the
tyre pressure is below 1.3 bar (19 psi,
130 kPa), do not continue driving.
(51
psi, 350 kPa).
Note: When pumping the sealant through
the tyre valve, the pressure may rise up to
6
drop again after approximately 30 seconds.
bar (87 psi, 600 kPa). The pressure will
10.
11.
During the inflation, switch the compressor
off briefly, to check the tyre pressure using
the gauge mounted on the compressor.
Note: It should not take longer than 10
minutes to inflate the tyre. If, after a
maximum of 10 minutes, the tyre has not
yet reached minimum pressure, the tyre
should not be used.
Consult a tyre repair centre or your
Dealer/Authorised Repairer, for advice
concerning the replacement of a tyre
after using a tyre repair kit.
Once the tyre has been inflated to the
required pressure, switch off the
compressor. If desired, the ignition may be
turned off after the compressor has been
turned off.
1.
Drive the vehicle for 3 km (2 miles) then
stop in a safe place. Carry out a visual
examination of the tyre’s condition.
2.
3.
Make sure that the sealant container section
is in its original position.
12.
13.
Remove the power connector from the
auxiliary power socket.
Screw the inflation hose connector firmly
onto the tyre valve.
Remove the inflation hose from the tyre
valve, by unscrewing it as quickly as
possible (counter clockwise).
4. Read the tyre pressure from the gauge.
243
XML to PDF by RenderX XEP XSL-FO Formatter, visit us at http://www.renderx.com/
| Categories | Land Rover, Range Rover |
|---|---|
| Tags | Land Rover |
| Model Year | 2014, 2015 |
| Download File |
|
| Document Type | Owners Manual |
| Language | English |
| Product Name | Range Rover Sport Handbook |
| Product Brand | Land Rover |
| Document File Type | |
| Publisher | landrover.com |
| Wikipedia's Page | http://en.wikipedia.org/wiki/Land_Rover |
| Copyright | Attribution Non-commercial |
(4 votes, average: 4 out of 5)
Automotive readers have rated 2014-2015 Land Rover Range Rover Sport Handbook Manual 4.0 out of 5.0 based on 4 product reviews. very good and for the first time
I search for heat device control system
Excellent source. Easy to follow
good to finally getting manual from here