L
Towing
During deployment of the powered tow bar, a
series of long warning tones will sound and the
green LED will flash. A double warning tone will
sound to confirm full deployment and all LEDs
will extinguish.
If the system needs to be reset, movement of
the powered tow bar will stop unexpectedly in
either the partially deployed or stowed position.
This will be accompanied by a continuous
warning tone. To reset the powered tow bar,
carry out the following steps:
To stow the powered tow bar, repeat the above
procedure using the tow bar on/off button (1)
and deploy/stow button (2).
1. Start the engine and run for longer than 2
seconds. Stop the engine and switch the
ignition off.
The powered tow bar must be returned
to the fully stowed position when not
in use.
2.
3.
Switch the ignition on, then off.
Press and hold button 1 until the green LED
illuminates on button 2. This should take
approximately 2 seconds.
Note: To stop movement of the powered tow
bar, press either button.
4.
Press and hold button 2 until the tow bar
has reached its fully deployed position. This
should take about 10 seconds. A double
warning tone will indicate that the tow bar
has reached the fully deployed position.
Note: During deployment of the powered tow
bar, if an obstruction/stall occurs, the green
LED will flash and a 10 second warning tone
will sound. Press the deploy/stow button while
the green LED is flashing to reverse movement
of the powered tow bar.
5.
Release button 2. The powered tow bar is
now reset.
Note: If there is debris on the mechanism (e.g.
ice), press and hold the deploy/stow button to
increase power output to the motor.
If the system has detected an error, a
continuous warning tone will sound. To clear
the system error, carry out the following steps:
Note: If the powered tow bar doesn't move or
is impacted but not damaged, it may need to be
reset. In cases of damage refer to your
Dealer/Authorised Repairer.
1.
Press and hold button 1 for more than 1
second.
2. If the error has been cleared, press and hold
button 2 for more than 1 second to move
the powered tow bar to the fully stowed, or
fully deployed position.
Powered tow bar reset
Note: Before attempting a reset procedure,
check the powered tow bar for damage. If the
powered tow bar is damaged, contact your
Dealer/Authorised Repairer.
3.
If the system error is not cleared, contact
your Dealer/Authorised Repairer.
If for any reason the procedures are
unsuccessful, for example the process was
interrupted, repeat the procedure from the
beginning. If problems persist, contact your
Dealer/Authorised Repairer.
LED's mounted in the deploy/stow button and
the on/off button are used to show the condition
of the powered tow bar system. Both button
LED's flashing indicate the system needs to be
reset. If only the on/off button is flashing, a
system error has been detected.
92
XML to PDF by RenderX XEP XSL-FO Formatter, visit us at http://www.renderx.com/
| Categories | Land Rover, Range Rover |
|---|---|
| Tags | Land Rover |
| Model Year | 2014, 2015 |
| Download File |
|
| Document Type | Owners Manual |
| Language | English |
| Product Name | Range Rover Sport Handbook |
| Product Brand | Land Rover |
| Document File Type | |
| Publisher | landrover.com |
| Wikipedia's Page | http://en.wikipedia.org/wiki/Land_Rover |
| Copyright | Attribution Non-commercial |
(4 votes, average: 4 out of 5)
Automotive readers have rated 2014-2015 Land Rover Range Rover Sport Handbook Manual 4.0 out of 5.0 based on 4 product reviews. very good and for the first time
I search for heat device control system
Excellent source. Easy to follow
good to finally getting manual from here