WHAT TO DO IN AN EMERGENCY
WARNING:
2. Turn off all unnecessary lights and acces-
sories in both vehicles.
D030A01A-AAT
IF THE ENGINE OVERHEATS
If your temperature gauge indicates overheat-
ing, you experience a loss of power, or hear
loud pinging or knocking, the engine is probably
too hot. If this happens to you, you should:
The gas produced by the battery during the
jump start operation is highly explosive. If
these instructions are not followed exactly,
serious personal injury and damage to the
vehicle may occur! If you are not sure how
to follow this procedure, seek qualified as-
sistance. Automobile batteries contain sul-
furic acid. This is poisonous and highly
corrosive. When jump starting, wear protec-
tive glasses and be careful not to get acid on
yourself, your clothing or on the car.
3. Attach the clamps of the jumper cable in the
exact order shown in the illustration. That is,
first, attach one clamp of the jumper cable to
the positive (+) post or cable of the dis-
charged battery. Then attach the other end
of the same cable to the positive (+) post or
cable of the booster battery. Next, using the
other cable, attach one clamp to the nega-
tive (-) post or cable of the booster battery.
Then attach the other end of that cable to a
solid metal part of the engine away from the
battery. Do not connect the cable to any
moving part.
1. Pull off the road and stop as soon as it is
safe to do so.
2. Place the gear selector lever in "P" (auto-
matic transaxle), or neutral (manual
transaxle) and set the parking brake. If the
air conditioning is on, turn it off.
o
If you should accidentally get acid on your
skin or in your eyes, immediately remove
any contaminated clothing and flush the
area with clear water for at least 15 minutes.
Then promptly obtain medical attention. If
you must be transported to an emergency
facility, continue to apply water to the affect-
ed area with a sponge or cloth.
3. If engine coolant is running out under the car
or steam is coming out from the hood, stop
the engine. Do not open the hood until the
engine coolant has stopped running or the
steaming has stopped. If there is no visible
loss of engine coolant and no steam, leave
the engine running and check to be sure the
engine cooling fan is operating. If the fan is
not running, turn the engine off.
4. Check to see if the water pump drive belt is
missing. If it is not missing, check to see that
it is tight. If the drive belt seems to be
satisfactory, check for engine coolant leak-
ing from the radiator, hoses or under the car.
(If the air conditioning had been in use, it is
normal for cold water to be draining from it
when you stop).
4.
Start the engine in the car with the booster
battery and let it run for a few minutes. This
will help to assure that the booster battery is
fully charged. During the jumping operation,
run the engine in this vehicle at about 2,000
rpm.
o
o
The gas produced by the battery during the
jump start operation is highly explosive. Do
not smoke or allow a spark or an open flame
in the vicinity.
The battery being used to provide the jump
start must be 12-volt. If you cannot deter-
mine that it is a 12-volt battery, do not
attempt to use it for the jump start.
5.
6.
Start your engine using the normal starting
procedure. After the engine starts, leave the
jumper cables connected and let the engine
run at fast idle or about 2,000 rpm for sev-
eral minutes.
Carefully remove the jumper cables in the
reverse order of attachment.
o
To jump start a car with a discharged bat-
tery, follow this procedure exactly:
If you do not know why your battery became
discharged (because the lights were left on,
etc.), have the charging system checked by
your Hyundai dealer.
1.
If the booster battery is installed in another
vehicle, be sure the two vehicles are not
touching.
3-2
Categories | Hyundai Manuals, Hyundai Atos Manuals |
---|---|
Download File |
|
Document Type | Owners Manual |
Language | English |
Product Brand | Hyundai, Atos |
Document File Type | |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)