1990 Land Rover Defender 90, 110, 130 Td5, Tdi, V8 Workshop Manual

n
DEFENDER
TORQUE  WRENCH
Tdi ENGINE
Bearing cap  to  cylinder  block ...................................
Camshaft  thrust   plate  to cylinder block ....................
Clutch  cover plate   to flywheel   .................................
Connecting   rod  to  cap .............................................
Dipstick tube assembly    to cylinder block .................
Dipstick mounting    bracket  to  inlet manifold ............
Earthing strap stud    to cylinder block ........................
Engine  mounting  foot  to cylinder block ...................
Housing flywheel t  o cylinder block   ..........................
Flywheel t o crankshaft  ..............................................
to cylinder  block ..................................
130
7 - 1 0
30
56
22
7 - 1 0
21
80
40
139
22
Oil filter  adaptor  to  cylinder block  ...........................
Oil pressure   switch ...................................................
Oil pump   cover to pump   body ................................
Oil pump   relief valve plug ........................................
Oil pump   to cylinder  block  ......................................
Oil pump strainer t   o oil  pump   .................................
Oil squirt  jet assembly  to  cylinder block  ..................
Oil strainer t  o mounting   bracket  ..............................
Plug    blanking  oil gallery .........................................
Plug - drain oil   sump  ................................................
40
15
20
27
22
40
14
22
32
40
25
Plug
.
drain  cylinder  block ........................................
Plug - drain   flywheel housing  ...................................
inlet  manifold  (boost take-off)  .......................
Plug
.
23
23
40
22
22
20
Side  cover to cylinder   block .....................................
Starter  motor  to  flywheel housing ............................
Sump t o ladderframe   ................................................
Sump  to
Sump  to cylinder
Support   brackets
block .........................
cover  ..........................
-
exhaust   manifold  to cylinder block  ........................
22
22
22
Vacuum  pump  to  cylinder block  ..............................
drive shaft gear to cylinder block     ................
Alternator and   heat  shield  to mounting   bracket .......
Adjusting  link to  alternator  .......................................
Adjusting  link to  pas  pump plate  ..............................
Cylinder  head  to  cylinder block   ...............................
Breather cylcone   to rocker  cover  .............................
Engine  lifting bracket  to  cylinder head  .....................
Electrical hamess clip   to cylinder head  .....................
Exhaust manifold  to  cylinder head    ...........................
Glow  plug  terminal  nut   ............................................
Glow  plug  to cylinder  head  ......................................
Heater  stud (water)   to  cylinder head ........................
Injector  clamp  stud  to cylinder head   ........................
Injector  clamp  to injector   nut ...................................
Inlet  manifold  to cylinder  head   ................................
Rocker  cover to cylinder   head ..................................
Rocker shaft  to cylinder   head ...................................
Tappet   adjusting nut  .................................................
Thermostat   housing  to  cylinder head .......................
Water  outlet t  o thermostat    housing  .........................
22
22
22
See section
7 - 1 0
22
22
20
3 - 5
15
15
6 - 1 0
20
20
3,5
28
22
22
7
75
22
22
22
22
22
22
.
4,5
water   temperature
to
....
Cowl  mounting   bracket  to front  cover .....................
Fan  assembly  to water  pump  hub  ............................
Front  cover plate  to cylinder block    ..........................
Front  cover plate  to front   cover ...............................
Front  cover to cylinder  block   ...................................
injector pump    to front cover    ...................................
Injector pump    stud  to front   cover ............................
.
.
28
.
.
.
28
28
28
.
6 - 1 0
15
Product Specification
CategoriesLand Rover, Land Rover Defender 110, Land Rover Defender 130, Land Rover Defender 90
Tags
Model Year1990
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 102 pages
Document TypeWorkshop Manual
LanguageEnglish
Product NameDefender 90, 110, 130 Td5, Tdi, V8
Product BrandLand Rover
Document File TypePDF
Publisherlandrover.com
Wikipedia's Pagehttp://en.wikipedia.org/wiki/Land_Rover
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field