1995 Land Rover Range Rover Classic Workshop Manual

V8i
FRONT COVER GASKET
Service repair no - 12.65.04
Refit
25.  Clean timing cover, clean block face.
26.  Lightly grease gasket faces.
1.
Remove crankshaft pulley.  See  Crankshaft
Pulley Assembly  Do not remove pulleys
Remove water pump pulley.
27.  Fit new gasket to block face.
28.  Apply hylosil to sump gasket.
29.  Clean threads of cover fixing bolts, apply Loctite
372 to threads.
30.  Fit timing cover, fit fixing bolts.  Tighten to 28
Nm.
31.  Fit generator support strut to front cover.
32.  Tighten sump to timing cover fixings to 10 Nm.
33.  Tighten sump fixings to 10 Nm.
34.  Lubricate distributor O ring.
2.
3.
4.
5.
6.
7.
8.
Release distributor cap clips.
Release plug leads from plugs and clips.
Place cap and leads to one side.
Turn engine until No. 1 piston is at T.D.C.
Check position of rotor arm.
Remove fixings securing power steering pump
bracket to water pump bracket.
9.
Remove power steering pump bracket from
water pump.
Remove clips securing wiring to generator
tensioner.
Disconnect distributor feed wire.
Pivot power steering pump away from front
cover, tighten pivot to retain in position.
Disconnect vacuum pipe from distributor.
Remove water pump bottom hose.
Disconnect oil pressure switch.
Disconnect heater hose at water pump.
Remove generator tensioner from water pump,
move tensioner aside.
Mark distributor position to front cover.
Remove distributor clamp, remove distributor.
See ELECTRICAL, Repair,  Distributor - V8i
Remove fixings sump to front cover.
Loosen four adjacent sump fixings.
Remove generator support strut from front cover,
move strut aside.
Loosen remaining front cover fixings and remove
front cover.
Remove front cover gasket.
35.  Fit distributor in position marked.
36.  Align oil pump drive, if distributor does not seat
correctly.
37.  Fit distributor clamp.  Tighten to 20 Nm.
38.  Locate generator tensioner on water pump
bracket.
39.  Connect heater hose, tighten clip.
40.  Connect oil pressure switch.
41.  Connect bottom hose, tighten clip.
42.  Connect vacuum pipe to distributor.
43.  Loosen power steering pump pivot, lower pump.
44.  Connect distributor feed wire.
45.  Connect wire ties to generator tensioner.
46.  Fit power steering pump bracket to water pump.
Tighten to 28 Nm.
47.  Fit power steering pump to bracket.
48.  Position distributor cap. Fit plug leads to plugs
and clips.
49.  Clip distributor cap in position.
50.  Fit water pump pulley.  Tighten to 10 Nm.
51.  Fit crankshaft pulley.  See  Crankshaft Pulley
Assembly
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
52.  Tension drive belts correctly.
53.
54.
Check ignition timing.
Refill cooling system.
REPAIR
9
Product Specification
CategoriesLand Rover, Range Rover
Tags
Model Year1995
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 767 pages
Document TypeOwners Manual
LanguageEnglish
Product NameRange Rover Classic
Product BrandLand Rover
Document File TypePDF
Publisherlandrover.com
Wikipedia's Pagehttp://en.wikipedia.org/wiki/Land_Rover
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field