INTRODUCTION
ABBREVIATIONS AND SYMBOLS USED IN THIS
MANUAL
Across flats (bolt size) ............................................ AF
After bottom dead centre................................... ABDC
After top dead centre......................................... ATDC
Alternating current ................................................. a.c.
Ampere ................................................................ amp
Ampere hour .................................................... amp hr
Before bottom dead centre................................ BBDC
Before top dead centre...................................... BTDC
Bottom dead centre ............................................. BDC
Brake horse power ................................................ bhp
British Standards .................................................... BS
Carbon monoxide .................................................. CO
Centimetre ............................................................. cm
Centigrade (Celsius) ................................................ C
Low tension ............................................................. l.t.
Maximum ............................................................ max.
Metre ........................................................................ m
Millilitre .................................................................... ml
Millimetre............................................................... mm
Miles per gallon .................................................... mpg
Miles per hour ...................................................... mph
Minute (angle) ............................................................ ’
Minus (of tolerance) ................................................... -
Negative (electrical) ................................................... -
Newton metres (torque) ........................................ Nm
Number ................................................................. No.
Ohms ................................................................... ohm
Ounces (force) ....................................................... ozf
Ounces (mass) ........................................................ oz
Ounce inch (torque) .......................................... ozf.in.
Outside diameter ................................................. O.D.
Part number ................................................... Part No.
Percentage............................................................... %
Pints ......................................................................... pt
Plus (tolerance) ......................................................... +
Positive (electrical) .................................................... +
Pound (force) .......................................................... lbf
Pounds inch (torque) .......................................... in.lbf.
Pound (mass)........................................................... lb
Pounds per square inch ..................................... P.S.I.
Ratio........................................................................... :
Reference .............................................................. ref.
Revolution per minute ..................................... rev/min
Right-hand ............................................................. RH
Second (angle) ........................................................... "
Second (numerical order)...................................... 2nd
Specific gravity ................................................... sp.gr.
Cubic centimetre ................................................... cm
Cubic inch ............................................................... in
3
3
Degree (angle) ............................................... deg or °
Degree (temperature)..................................... deg or °
Diameter ............................................................... dia.
Direct current......................................................... d.c.
Electronic Control Unit ........................................ ECU
Fahrenheit ................................................................. F
Feet ........................................................................... ft
Feet per minute .................................................. ft/min
Fifth ........................................................................ 5th
First ........................................................................ 1st
Fluid ounce .......................................................... fl oz
Foot pounds (torque)............................................ lbf ft
Fourth..................................................................... 4th
Gramme (force) ........................................................ gf
Gramme (mass) ........................................................ g
Gallons ................................................................... gal
High tension (electrical)........................................ H.T.
Internal diameter ................................................... I.D.
Inches of mercury.............................................. in. Hg
Inches ...................................................................... in
Kilogramme (force)................................................. kgf
Kilogramme (mass.) ................................................ kg
Kilogramme centimetre (torque)....................... kgf.cm
Square centimetres ............................................... cm
Square inches ......................................................... in
2
2
Standard wire gauge ......................................... s.w.g.
Synchroniser/Synchromesh .......................... synchro.
Third ....................................................................... 3rd
Top dead centre .................................................. TDC
United Kingdom...................................................... UK
Vehicle Identification Number ............................... VIN
Volts ......................................................................... V
Watts ....................................................................... W
Kilogramme per square millimetre ................. kgf/mm
Kilogramme per square centimetre ................. kgf/cm
2
2
Kilogramme metres (torque) .............................. kgf.m
Kilometres .............................................................. km
Kilometres per hour ............................................. km/h
Kilovolts................................................................... kV
Left-hand ................................................................ LH
Left-hand steering ............................................. LHStg
Left-hand thread ............................................... LHThd
Litres ..................................................................... litre
SCREW THREADS
British Standard Pipe ........................................... BSP
Unified Coarse .................................................... UNC
Unified Fine ......................................................... UNF
INFORMATION
9
Categories | Land Rover, Land Rover Defender |
---|---|
Tags | Land Rover |
Model Year | 1996 |
Download File |
|
Document Type | Workshop Manual |
Language | English |
Product Name | Defender 300 Tdi |
Product Brand | Land Rover |
Document File Type | |
Publisher | landrover.com |
Wikipedia's Page | http://en.wikipedia.org/wiki/Land_Rover |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)