1996 Land Rover Defender Worshop Manual 300 Tdi

57
STEERING
POWER STEERING BOX
8.  Remove 2 bolts securing tie bar to steering box
and move aside.
Service repair no - 57.10.01
9.  Remove filler cap from power steering fluid
reservoir.
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
10.  Position suitable container under steering box.
11.  Disconnect feed and return pipes from steering
box and drain fluid.
remove and refit procedures are required, it may
be necessary to remove the undertray See
CHASSIS AND BODY, Repair, Front undertray .
General precautions
Whenever any part of system, is removed or
disconnected, utmost cleanliness must be
observed.
Disconnected ports and hoses must be
plugged to prevent ingress of dirt. If metal
sediment is found in system, establish cause,
rectify and flush system.
Do not start engine until reservoir is full as
pump will be damaged.
Metric pipe fittings are used with ’O’ ring pipe
ends on fittings to steering box.
Follow normal ’O’ ring replacement procedure
whenever pipes are disconnected.
Ensure compatible metric components when
fitting replacement pipes.
12.
Plug open pipes and steering box ports to
prevent ingress of dirt. Refit fluid reservoir filler
cap.
13.
14.
15.
Centralise steering  See Centralise steering
box .
CAUTION: After refitting steering linkage
parts follow correct procedure to ensure
that road wheels, steering box and
steering wheel are correctly positioned relative to
each other when in straight ahead condition.
Remove pinch bolt securing lower shaft
universal joint to power steering box.
Remove 4 bolts and 2 tab washers securing
steering box to chassis side member.
Withdraw steering box.
16.
17.
NOTE: When drag link is disconnected
from steering box, travel available at
steering wheel to each full lock is not
equal.
Clean all mounting faces, unions etc. prior to
refitting.
Refit
18.
Remove
Position steering box to chassis side member,
ensuring locating peg is engaged. Fit tab
washers and tighten bolts to 81 Nm (60 lbf/ft).
Fit pinch bolt and nut securing universal joint to
power steering box spline. Tighten to 25 Nm (18
lbf/ft).
Secure tie bar to mounting arm and steering box.
Tighten fixings to 81 Nm (60 lbf/ft), starting with
tie bar to mounting nut, then loosen fixings by
one complete turn.
1.
2.
Site vehicle on level surface.
Apply park brake, chock rear wheels, raise
vehicle and locate axle stands. Alternatively,
raise vehicle on a hoist.
19.
20.
3.
4.
Remove road wheel.
Remove panhard rod  See FRONT
SUSPENSION, Repair,  Panhard rod .
Disconnect steering damper from drag link.
Disconnect drag link from drop arm, see J6305
on opposite page, using a suitable extractor.
Slacken, but do not remove nut securing tie bar
to mounting arm.
5.
6.
21.
22.
Check steering box and adjust if necessary See
Adjustment,  Power steering box - adjust .
Refit drag link to drop arm and tighten nut to 40
Nm (30 lbf/ft). Fit new split pin to retaining nut.
7.
4
REPAIR
Product Specification
CategoriesLand Rover, Land Rover Defender
Tags
Model Year1996
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 450 pages
Document TypeWorkshop Manual
LanguageEnglish
Product NameDefender 300 Tdi
Product BrandLand Rover
Document File TypePDF
Publisherlandrover.com
Wikipedia's Pagehttp://en.wikipedia.org/wiki/Land_Rover
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field